DESCRIPTION AND BENEFITS
MODELS
REPLACEMENT PARTS AND ACCESSORIES
QUESTIONS AND ANSWERS
Aerosol Can Depressurizing System
BRAND

questions and answers

 

PUNCTURING UNIT

How does the Puncturing Unit operate?
The Aerosolv unit threads directly to the 2” bung of any 30- to 55-gallon drum. The filter is installed on the 3/4” bung. Insert the aerosol can (inverted) into the Aerosolv housing. Lower the sliding cap and lock into place. Push handle down firmly until completely depressed and hold in place while can releases initial pressure and contents. Allow the contents of the can to drain into the collection drum (about 20 seconds).

ALWAYS OPERATE AEROSOLV SYSTEM OUTDOORS OR IN A WELL VENTILATED AREA

THE DRUM

Must Aerosolv be installed only on 55-gallon drums?
No, all industry standard drums have 2” openings. However, Aerosolv should not be installed on a drum smaller than 30-gallon capacity to allow proper displacement of compressed gas released during puncturing.

How many spent aerosols can be punctured into a drum?
Approximately 4,200 cans can be punctured before the drum is at maximum recommended capacity. The drum should not be filled more than 75% full to provide proper displacement for released contents.

What do you do once the liquids reach the recommended “full” capacity?
Simply call the waste handler who is handling your other hazardous waste and manifest according to collected contents.

Must a waste-profile sample be drawn from each drum, prior to transport by a waste handler?
A waste profile of a worst-case scenario, whereby all known aerosol residuals are listed, excluding pesticides and insecticides, is available. Reputable waste handlers should accept this profile for co-mingled residuals, thus avoiding the expense of profiling the drum. Click here for Waste Profile.

What does it cost to dispose of the collected liquids in the drum?
Determined by each country where the system will be used.

Does any compressed gas remain in the drum?
The compressed gas seeks escape through the point of least resistance, which is the filter. However, a minimal amount of gas may remain in the drum. By leaving the “last” can punctured within the Aerosolv housing until puncturing is resumed, an effective prolonged seal can be maintained.

Can pressure build in the drum?
The filter relieves at 3 psi, eliminating the possibility of unsafe pressure within the drum. Additionally, the activated carbon portion of the filter has been designed to serve as a secondary flame arrestor.

THE SYSTEM

How long does it take to puncture cans with Aerosolv?
It only takes 15-20 seconds for the can to be depleted after puncturing. One Aerosolv customer has punctured as many as 500 on a one-man seven hour shift.

Will the Puncturing Unit accept any size aerosol can?
The system is designed to puncture any industry standard aerosol can, regardless of length. Special gaskets are available for smaller diameter cans.

How does the filter work?
It is composed of two parts: a coalescing lower portion and an activated carbon upper portion. The coalescing portion collects microscopic airborne liquids from the gas and combines them into droplets which collect within the filter chamber. The activated carbon adsorbs hydrocarbons and removes odor from the “dry” gas which has passed through the coalescing portion. It effectively reduces VOC’s from the escaping gas, resulting in total hydrocarbon emissions 75% less than the 300 ppm desired limitations.

THE MAINTENANCE

What maintenance does the Aerosolv Puncturing Unit require?
Periodic maintenance should include: replacement of gasket which is installed inside the unit that provides a seal against the can and cleaning/lubricating the puncture pin will enhance the unit longevity. Cleaning the unit where the liquids evacuate to the drum will decrease back-pressure.

When does the filter need to be changed?
Filter life is 9 months or 2,250 cans with changing the Carbon Cartridge (upper portion) twice; cartridge life is 3 months or 750 cans; more frequent change-outs may be necessary based on use. The activated carbon will meet its maximum adsorption at this time and require replacement.

THE RECYCLING

How much can scrap steel recycling be increased with Aerosolv?
Generally, four aerosol cans equal one pound of steel. American industry consumes 3 billion aerosol cans per year, amounting to 375,000 tons of steel.

Can the liquids collected into the drums be reclaimed or recycled?
Yes, if chlorinated and non-chlorinated liquids are collected into separate drums. Chlorinated liquids (primarily solvents) can be recycled in-house as “parts cleaning solvent”; non-chlorinated liquids (primarily paints) can be reclaimed. Either method may qualify for “waste minimization credit”.

THE RULES

Are there any aerosols that should not be co-mingled when collecting into the drum?
Yes, caustics (such as oven cleaners) and pesticides or insecticides should not be collected into a drum with other liquid residuals. They can, however be collected into segregated single-content drums designated “pesticides only”, “insecticides only”, or “caustics only”. Also, white metals-typically labeled as “cold galvanized” should be separated and not co-mingled with any other aerosol residuals.

Are all aerosols considered hazardous waste?
Yes, but not because of the primary product they contain. Spent aerosol cans would be considered empty, and therefore exempt from regulation, were it not for the fact that the propellant compressed gas is reactive to heat and is still present in an empty can (40 CFR 261.23 (a) (6).

Is the puncturing of aerosol cans with Aerosolv considered treatment?
No, however, according to the EPA's Office of Solid Waste: a steel aerosol can that does not contain a significant amount of liquid (e.g., a can that has been punctured and drained) would meet the definition of scrap metal (40 CFR 261.1(c) (6)), and, if it is to be recycled, would be exempt from regulation under 40 CFR 261.6(a) (3) (iv). Scrap metal that is recycled is exempt from RCRA regulation under this provision even if it is hazardous waste, so generators need not make a hazardous waste determination.

How do I properly dispose of my spent Activated Carbon Filter?

Beginning June 1, 2015, Katec Inc. will provide FREE labels by request to take back the spent Activated Carbon Filters. This industry first program will then fully recycle the carbon filter processing each component accordingly. The spent carbon will be cleaned, reactivated, and put back into use and the plastic housing will be completely recycled eliminating the filter waste stream entirely.

Does the procedure require any permitting from the Air Quality Control Board?

No, permitting is only required when processing 15 pounds or more per day, which is not the case with the Aerosolv system. Permitting generally applies to gas-filling facilities: welding gases, large gas cylinders, etc..

Why is the anti-static wire necessary?
In many cases, there is an OSHA requirement for grounding of “vessels” to prevent any build-up of the static electricity being transferred to a drum. The anti-static wire grounds the drum and the Aerosolv unit simultaneously. The Aerosolv system itself is not capable of generating a static charge. It is non-powered and utilizes a non-sparking puncture pin.